Newly shared Cisco 300-610 exam learning preparation program! Get the latest 300-610 exam exercise questions and exam dumps pdf for free! 100% pass the exam to select
the full Cisco 300-610 dumps: https://www.leads4pass.com/300-610.html the link to get VCE or PDF. All exam questions are updated!
Lead4pass offers the latest Cisco 300-610 PDF Google Drive
[Latest updates] Free Cisco 300-610 dumps pdf download from Google Drive: https://drive.google.com/file/d/1pKCu9naejhuwp7h1mU5zMyIAkKauY7-9/
latest updated Cisco 300-610 exam questions and answers
QUESTION 1
What is a design consideration when implementing FSPF?
A. Routes are based on the domain ID.
B. Routes are based on the distance vector protocol.
C. FSPF runs only on F Ports.
D. FSPF runs on a per-chassis basis.
Correct Answer: A
Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/5_0/configuration/guides/fabric/nxos/cli_fabric/fspf.html
QUESTION 2
What are two characteristics of VRF-Lite on the Cisco NX-OS platform? (Choose two.)
A. Layer 3 interfaces can belong to multiple VRFs.
B. VRF-Lite interfaces can be Layer 2.
C. Overlapping IP addresses are permitted on different VRFs.
D. Interfaces that belong to VRFs can be physical or logical.
E. VRF-Lite interfaces support MPLS.
Correct Answer: CD
Reference: https://www.cisco.com/c/en/us/td/docs/routers/connectedgrid/cgr1000/ios/software/15_4_1_cg/vrf_cgr1000.html
QUESTION 3
What are two functions of a Network Services Orchestrator in an NFV environment? (Choose two.)
A. It operates at the resource-facing services layer and provides overall lifecycle management at the network service level.
B. It provides an API-based northbound interface for transparent integration with systems that operate at the resourcefacing services layer.
C. It provides a standards-based southbound interface for transparent integration with systems that operate at the
customer-facing services layer.
D. It provides a standards-based northbound interface for transparent integration with systems that operate at the
customer-facing services layer.
E. It operates at the customer-facing services layer and provides the management interface for the virtual network
devices.
Correct Answer: AB
Reference: https://www.cisco.com/c/en/us/td/docs/net_mgmt/msx/3_4/solution_overview/Cisco_VMS_Sol_Overview.pdf
QUESTION 4
An engineer is designing a disaster recovery solution. In the event of a node failure, the solution should either direct all
of the traffic to another node, or load-balance the traffic across the remaining nodes. Which solution should be
implemented in the design?
A. active/active
B. cold standby
C. active/passive
D. warm standby
Correct Answer: A
QUESTION 5
An engineer must build a VXLAN flood-and-learn network. The customer requires the solution to be based on the IETF
documented practice in RFC 7348. The solution must use broadcast, unknown unicast, and multicast (BUM) and
include the efficient BUM and short BUM replication modes that use only shared trees.
Which technology meets these requirements?
A. MVPN
B. PIM sparse mode
C. PIM SSM
D. Bidirectional PIM
Correct Answer: B
Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/UCS_CVDs/flexpod_esxi70_vxlan_evpn_design.html
QUESTION 6
Which two automation requirements are met when Puppet is used? (Choose two.)
A. Enable clients to pull changes without installing an agent.
B. Enable clients to pull changes to configuration files.
C. Enable one-off infrastructure changes to be performed manually.
D. Immediately push configuration updates to servers.
E. Provide support for writing new modules in Python.
Correct Answer: AD
Reference: https://blogs.cisco.com/datacenter/cisco-nx-os-and-puppet-agentless-data-center-automation
QUESTION 7
Which two automation requirements can be met by using Puppet? (Choose two.)
A. Push configuration updates immediately to servers.
B. Enable clients to pull changes to configuration files.
C. Enable clients to pull changes without installing an agent.
D. Provide support for writing new modules in Python.
E. Enable one-off infrastructure changes to be performed manually.
Correct Answer: AB
Reference: https://www.cisco.com/c/dam/en/us/products/collateral/servers-unified-computing/ucs-c-series-rackservers/whitepaper_c11-740103.pdf
QUESTION 8
Refer to the exhibit.
An engineer must assign multiple Fibre Channel IDs to a single port channel.
Which two features must be enabled this goal? (Choose two.)
A. SAN Pin Groups on the Cisco UCS Fabric Interconnects.
B. NPV feature on the Cisco MDS Series.
C. end-host mode feature on the Cisco UCS Fabric Interconnects
D. NPIV feature on the Cisco MDS Series
E. Smart Zoning feature on the Cisco UCS Fabric Interconnects
Correct Answer: BD
QUESTION 9
An engineer configured the OSPF protocol in the vPC topology. During the catastrophic failure of one of the vPC
member switches, the traffic was routed to a black hole. This route was caused by the long convergence time caused by
the delay of the vPC member switch reboot. After the failure, the engineer rebooted both switches, but the secondary
switch powered on before the primary one. It caused all the vPCs to be shut down due to consistency-check violations.
Which two features must be used to prevent these situations from happening in the future? (Choose two.)
A. peer-gateway
B. ip arp synchronize
C. delay restore
D. auto-recovery
E. system priority
Correct Answer: CD
QUESTION 10
Which address pool is used when a vHBA template is created?
A. MAC
B. WWPN
C. IP
D. UUID
Correct Answer: B
Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/2-1/b_UCSM_GUI_Configuration_Guide_2_1/b_UCSM_GUI_Configuration_Guide_2_1_chapter_011010.html
QUESTION 11
Which two configurations are available by using a service profile template in Cisco UCS Manager? (Choose two.)
A. number of vHBAs
B. ARP entries
C. UUID assignment
D. VXLAN membership
E. target server
Correct Answer: AC
Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/cli/config/guide/2-2/b_UCSM_CLI_Configuration_Guide_2_2/b_UCSM_CLI_Configuration_Guide_2_2_chapter_0100000.html
QUESTION 12
An engineer is designing a data center that uses FCIP. How is QoS configured in this environment?
A. A separate DSCP value and CoPP must be configured for all FCIP traffic and another for all of the FCIP frames in the
data connection.
B. A separate DSCP value must be configured for all FCIP VSAN traffic.
C. A separate DSCP value and priority queuing must be configured for all FCIP traffic.
D. Two separate DSCP values must be configured, one of all of the FCIP frames in the control TCP connection and
another for all of the FCIP frames in the data connection.
Correct Answer: D
Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/5_0/configuration/guides/ipsvc/nxos/ipsvc/cfcip.html
QUESTION 13
A network engineer designs a Cisco Nexus data center network for a client-server farm using a pair of Nexus 9000
Series Switches in a vPC setup. Each server connects with two interfaces to both Nexus switches. The Nexus switches
must always initiate the negotiation with the server.
Which feature should be used in this design to ensure traffic is forwarded from the server to the data center network?
A. PAgP mode desirable
B. LACP mode auto
C. LACP mode active
D. PAgP mode auto
Correct Answer: C
Reference: https://www.cisco.com/c/en/us/td/docs/ios/12_2sb/feature/guide/gigeth.html
Summarize:
Exam-Box free to share Cisco 300-610 exam exercise questions, 300-610 pdf! Lead4pass updated exam questions and answers throughout the year!
Make sure you pass the exam successfully. Select lead4Pass 300-610 to pass Cisco 300-610 exam “Designing Cisco Data Center Infrastructure (DCID)“.
ps.
Latest update Lead4pass 300-610 exam dumps: https://www.leads4pass.com/300-610.html (95 Q&As)
[Latest updates] Free Cisco 300-610 Dumps pdf download from Google Drive: https://drive.google.com/file/d/1pKCu9naejhuwp7h1mU5zMyIAkKauY7-9/